Suisse Pliage — Installation guide

FLAT PARAPET COPING INSTALLATION

Technical guide — step-by-step installation for building professionals.

📋 Technical tutorial

Complete installation procedure for a flat parapet coping with clip-on system on grooved brackets — from surface preparation to finishing.

🔧 Required tools

► Drill / screwdriver

► Drill bits (concrete / block)

► Anchors and stainless screws

► Pencil / tape measure / level

► Rubber mallet

► Snips or hacksaw

📐 General view

Part 01

⚒ BRACKET INSTALLATION

1. Nettoyer la surface sur laquelle seront fixées les couvertines

Remove dust, rubble and loose parts. The surface must be clean and sound before any fixing.

2. Placer l'angle de couvertine, puis tracer les extrémités

Position the coping angle at the end. Mark with a pencil the bracket locations along the parapet.

3. Positionnement des supports

Position the grooved brackets according to the markings. Check alignment and plumb before drilling.

4. Perçage des supports et du mur

Drill through the bracket and wall simultaneously with a bit suitable for the material (concrete, block, brick).

5. Installation des chevilles et vissage

Insert the anchors into the drilled holes. Firmly fix the grooved brackets with stainless screws.

💡 Practical info — Grooved bracket spacing

► Every 1.50 m for copings of 3 m in length

► Every 1.00 m for copings of 2 m or less

Part 02

🏠 COPING INSTALLATION

6. Clipsation de la couvertine

Engage the coping on the first bracket starting from one end. Clip firmly onto each grooved bracket until it clicks into place. Use a rubber mallet if needed to avoid deforming the piece.

7. Pose d'une seconde couvertine

Position the second coping ensuring sufficient overlap with the first (minimum 30 mm recommended). Check alignment before clipping onto the next brackets.

8.1 Ajout d'une éclisse extérieure

Place the external splice at the junction between two copings to ensure waterproofing and conceal the expansion joint.

8.2 Ajout d'une éclisse intérieure (alternative)

Alternative to the external splice: inserted inside the profile for a more discreet appearance from the outside.

9. Ajout des embouts de finition

Finish the ends with closure caps to prevent water infiltration and insect entry. Snap into place until fully engaged.

✅ Summary — 9 installation steps

1. Cleaning the parapet surface

2. Positioning coping angle and marking ends

3. Bracket positioning rainurés

4. Drilling brackets and wall

5. Installing anchors and screwing des supports

6. Clipping the first coping

7. Installing remaining copings with overlap

8. Installing splices (external or internal)

9. Installing end caps

Need custom copings?

CONFIGURE MY COPING ONLINE

► ACCESS THE CONFIGURATOR

Suisse Pliage — Installation guide

FLAT PARAPET COPING INSTALLATION

Technical guide — step-by-step installation for building professionals.

📋 Technical tutorial

Complete installation procedure for a flat parapet coping with clip-on grooved bracket system.

🔧 Required tools

► Drill / screwdriver

► Drill bits (concrete / block)

► Anchors and stainless screws

► Pencil / tape measure / level

► Rubber mallet

► Snips or hacksaw

📐 General view

Part 01

⚒ BRACKET INSTALLATION

1. Nettoyer la surface

Remove dust, rubble and loose parts. The surface must be clean and sound before any fixing.

2. Placer l'angle et tracer les extrémités

Position the coping angle at the end. Mark with a pencil the bracket locations along the parapet.

3. Positionnement des supports

Position the grooved brackets according to the markings. Check alignment and plumb before drilling.

4. Perçage des supports et du mur

Drill through the bracket and wall simultaneously with a bit suitable for the material (concrete, block, brick).

5. Installation des chevilles et vissage

Insert the anchors into the drilled holes. Firmly fix the grooved brackets with stainless screws.

💡 Bracket spacing

► Every 1.50 m for 3 m copings

► Every 1.00 m for copings 2 m and under

Part 02

🏠 COPING INSTALLATION

6. Clipsation de la couvertine

Engage the coping on the first bracket. Clip firmly until it clicks. Use a rubber mallet if needed.

7. Pose d'une seconde couvertine

Minimum 30 mm overlap recommended. Check alignment before clipping.

8.1 Éclisse extérieure

Place the external splice at the junction to ensure waterproofing and conceal the expansion joint.

8.2 Éclisse intérieure (alternative)

More discreet alternative: inserted inside the profile.

9. Embouts de finition

Finish ends with closure caps. Snap into place until fully engaged.

✅ Summary — 9 steps

1. Surface cleaning

2. Angle placement + marking

3. Bracket positioning

4. Drilling brackets + wall

5. Anchors + screwing

6. Clipsation première couvertine

7. Next copings + overlap

8. Ext. or int. splices

9. End caps

Need custom copings?

CONFIGURE MY COPING

► ACCESS THE CONFIGURATOR